The sunshade on the dashboard has been completely removed, the center console has become flatter, and the front view has been further improved; both the main and passenger positions are equipped with tuyere cup holders, which is a classic design from the second generation model (the third generation flying degree is only provided by the main driver side). In addition to the traditional glove box, there is a small independent locker on the center console on the side of the co-driver-this is not a high-tech configuration, but it improves the practicability of the whole vehicle.
The simplest item in the high temperature test is the exposure test, in which the vehicle is parked in the hot sun with the front facing west, and a temperature display patch is affixed to the engine cover, dashboard, steering wheel and other key parts of the vehicle, and the temperature in the car is as high as 70 or 80 degrees. Then test the door handle, dashboard, sunshade, air conditioning outlet and other internal and external accessories for abnormal noise or functional failure.
In terms of temperature management, the early growth stage of spring cauliflower cultivation was in the low temperature season, and the growth was small, while the plant size of broccoli was closely related to the flower head yield, and the temperature increased rapidly in the later growth stage, which was disadvantageous to the flower bud differentiation and flower ball formation of broccoli. Therefore, in the field management, it is required to do a good job of heat preservation in the early stage of growth to prevent freezing. Those cultivated in greenhouse should be closed in time to keep warm, those cultivated in open field should be trenched and drained as soon as possible to prevent freezing, and the remedial method of covering the floating surface of sunshade net should be adopted in case of sudden frost or freezing weather. In the later stage of growth, after the temperature rises in April, the protected cultivation should do a good job of ventilation and cooling in time, and the flower heads should be harvested in time after maturity.
1. The structure of the window should be able to control sunlight exposure and limit the area ratio of the window wall. For buildings with larger window area, endothermic glass, heat reflection glass or shading measures should be considered, such as sunshade panels, eaves, eaves, balconies, blinds, curtains and so on. Natural air can be directly used as a source of energy when the outdoor temperature is low, so the structure of the window should be able to open or set a natural vent on it.
Among them, Lijin FA two-plate high-performance large injection molding machine adopts a unique two-plate clamping structure and an optimal combination design that integrates mechanical, hydraulic and control. The maximum clamping force can reach 70000KN. Its efficient and stable control system is more suitable for auto parts molding and lightweight requirements, with high-quality servo pump group, minimizing production energy consumption. It is suitable for the intelligent production demand of large-scale deep cavity products, and the models in the auto parts industry are concentrated in 450-4500 tons. It is mainly used to produce automobile bonnet, front and rear bumper, exterior decoration electroplated parts, front grille, dashboard, interior trim, door panel, sunshade panel, seat side cover and other parts, equipped with professional injection molding machine controller, single cylinder injection system, high repetition precision, large modulus and opening stroke, high quality hydraulic sealing technology. Improve the durability and reliability of the machine.
(2) adjustable shading facilities should be used in ultra-low energy consumption buildings. The heat absorbed by the sun absorbed by the external sunshade surface can be adjusted automatically or manually according to the sun height angle and outdoor weather conditions, and the proportion of the sun absorbed by the external sunshade surface is smaller than that of the inner or middle shade. It is the most suitable shading form for ultra-low energy consumption buildings. The schematic diagram of the adjustable external shade and adjustable sunshade of the lifting louver is shown in figure 10;
At present, spray-free plastics have been successfully used in side skirts, central control panels, DVD panels, glove boxes, sunshades, instrument panels and other automotive parts in the automotive field. Bioplastics bioplastics are produced by using original plants as raw materials, such as sugar cane and corn, under the action of microorganisms. Commonly used plastics generally use petroleum products, and there are often small molecular harmful substances that do not fully react, while bioplastics, due to the use of low-toxic and low-harm renewable raw materials, greatly reduce the VOCs volatilization in the car after turning it into automobile interior parts. In addition, this bioplastic can be used for subsequent use, and is a more environmentally friendly type of plastic.
In particular, it highlights the advantages of insulating glass, such as thermal insulation, sound insulation, anti-dust pollution, safety and so on. The product features reasonable use space: no special shutter installation space is needed. It is a combination of aluminum blinds in the hollow glass window, which uses magnetic force to show the shrinkage, flattening and switching effect of the built-in glass shutters. The technology combines the external sunshade device, the hollow glass window and the interior curtain into one, and has the effect of all four. The sexual seal ensures that the blinds are clean and free from contamination, avoiding complex cleaning work. The blades do not need to be cleaned to achieve the effect of saving time and effort.